- CATALOG
- Spare parts
- CZ Parts
- CZ 75 SP-01 Spare Parts
- CZ Shadow 2 spare parts
- CZ 75 Tactical Sport/Czechmate spare parts
- CZ P10 spare parts
- CZ P07/P09 Spare Parts
- CZ P-01 Spare Parts
- CZ Scorpion Evo 3 Spare Parts
- Aluminium / Brass Grips for CZ
- G10 Grips for CZ
- Short Grips / Magwells for CZ
- CZ 75 Compact Grips
- CZ 97 Grips
- Magazine / Base Pad for CZ
- Sight / Dot for CZ
- Trigger for CZ
- CZ 455-457 Spare Parts
- KMR Arms Parts
- Tanfoglio Parts
- 1911/2011 Parts
- Glock parts
- Arex Parts
- Arsenal Firearms Parts
- Beretta Parts
- Walther Parts
- Ruger 22/45 Mark IV Parts
- Sig Sauer Parts
- Canik Parts
- Heckler & Koch Parts
- HS Parts
- XDM Parts
- Makarov Parts
- Laugo Arms Parts
- Revolver
- Magazine / Base Pad
- Sight / Dot
- Pistol Flashlight/Flashlight
- Springfield Armory
- CZ Parts
- Rifle/Shotgun
- Shotgun
- PCC/RONI
- Rifle Scope / Red Dot
- Holsters and Belts
- Clothing
- Timer and Chronographs
- Bags and Backpacks
- Accessories
- Reloading Machines
- Maintenance and cleaning
- Promotions
- Gun shop
- Softair
- Spare parts
- New arrival
- Special offers
- Gun shop
- About us
- All brands
- General terms and conditions
- Shipping
- Return of the products
- Privacy Policy
- Contacts
- Became a reseller
This is a complete set of Alpha-Xi Pouch Inlays in the color of your choice.
These inlays will fit into all the various pockets on the Alpha Xi pouch body. check the fit first for all pieces before removing the 3M tape from the back. Most pockets are unique and require their specific piece. Do not glue an insert in the pocket you plan to attach the Ball Joint to.
Please note that these inlays have a protective transparent film on their front and 3m adhesive tape cover on their back. Both should be peeled off before installation..
In order to install the inlays do the following:
- Carefully break the pieces out of their frame. There are several small bridges holding them in place which can be broken by hand.
- If you wish, you can use a knife to clean off the tails left by the bridges, but these won’t really be visible once installed.
- Check you have the correct inlay in hand for the pocket you are addressing. Peel off the transparent film from the front, as well as the 3M adhesive cover from the back.
- Position each inlays into their correct pockets in the pouch body and fit them in place.
Should you wish you remove the inlays after installation, you can do so using the small holes drilled through the pouch body. In order to access these holes, you will need to remove all plastic spacers first. Then, using a sharp tool (like a small hex key) you can push on the inside of the inlay until it comes loose in the corner. Then, gently work it out of its pocket. Note that the inlay may break when removed.
Customers who bought this product also bought:
Recoil Spring CZ 75 SP-01 Shadow / Shadow 2/TS - Toni System
Leather Document Binder (13 x 18 x 2,5 cm) - DAA
Customers who bought this product also bought:
24 other products in the same category:
Other Customers Also Bought These
Thumb rest for Glock,Thumb rest for Tanfoglio,Thumb rest for 1911/2011
Thumb rest 3 holes - Toni System
Grips / Funnels for 1911/2011,1911/2011 spare parts
Grip Screw Set 4 pc Torx T15 for 1911 Pistols - X-Ray Parts
Not Right? Try One Of These Instead